Workplace safety

PPE Detection Software for CCTV and Site Video

Ceptory checks every worker on camera for a hard hat, a hi-vis vest and gloves. Upload a clip to get every violation with its timestamp, or connect your site cameras and get an alert, with the frame, the moment someone walks into a PPE zone without their gear.

Attach a clip and send. The task is filled in; change it to anything you need.

Example footage: a warehouse loading bay, the same clip you can run PPE checks on in the dashboard.

Gear checked

Helmet, vest, gloves

Choose any combination per camera.

Live check

Every 10 s

Every worker inside the zone you draw.

Recorded video

Clips up to 2 GB

Every violation with its timestamp.

How it works

Check a clip in minutes, or watch cameras around the clock

Upload a clip

For footage you already have: an incident, a shift, a day on site.

  1. 01Attach a recording (MP4, MOV and most video formats, up to 2 GB) in the box at the top of this page or in a new dashboard chat.
  2. 02Send the prompt as it is, or change it: “Who isn't wearing a hard hat in this video? Give timestamps.”
  3. 03Get the answer with timestamps and frames, ask follow-ups, and export a report to PDF or Word.

Watch site cameras for missing PPE

Pick which gear is required, draw the PPE zone, and Ceptory checks everyone in it every 10 seconds.

  1. 01Open Cameras and choose Connect a camera. PPE check is already picked when you come from this page.
  2. 02Choose the source: a webcam on this computer, an IP camera or NVR (RTSP or ONVIF, through Ceptory Edge or the desktop app), a live stream pushed from OBS, a drone or an encoder, or one of our example videos.
  3. 03Draw the area to watch: the area where PPE is required, such as the site entrance, a loading bay or the area under a crane.
  4. 04Set the rules: which gear everyone in the zone must wear (helmet, hi-vis vest, gloves) and how long to wait before alerting on the same person again.
  5. 05Choose where alerts go and how long a clip to keep, then save. The camera starts watching straight away.

What it finds

What PPE Detection picks up

No hard hat

Workers in the zone without a safety helmet or hard hat, the most common PPE rule on construction sites, plants and warehouses.

No hi-vis vest

People without a high-visibility vest or jacket near vehicles, forklift lanes, loading docks and roadside work.

No gloves

Bare hands where gloves are required. Hands are often out of view, so this works best on close-up cameras over workstations.

Who and where

Each finding names the camera and zone and boxes the person, so a supervisor can tell exactly who to talk to.

Rules you control

Set it up for your site

Required gear
Helmet, hi-vis vest and gloves, each on or off per camera. Helmet and vest are on by default.
PPE zone
Draw the area where the rule applies; people outside it are ignored (canteens, offices, the public road).
Re-alert wait
A cooldown (5 minutes by default) so one person without a helmet raises one alert, not sixty.
Check rate
A frame every 10 seconds by default, adjustable per camera.

Every alert

What each alert includes

  • The frame that triggered it, with the person, object or vehicle boxed
  • A 10, 20 or 30 second clip around the moment (half before, half after), if you turn clips on
  • Camera name, site, time and the rule that fired
  • Delivery to Slack, Microsoft Teams, Discord, email or a signed webhook, plus push to the Ceptory phone app and an optional alarm on the monitoring desk
  • One click to turn the alert into a full incident report you can export to PDF or Word

Use cases

Where teams use it

Construction sites

Hard hat and vest checks at the gate, on scaffolding approaches and around cranes and excavators.

Warehouses and logistics

Hi-vis vests in forklift lanes and on loading docks, where most vehicle-pedestrian incidents happen.

Manufacturing plants

Helmets and gloves at machines and on the production floor, by shift and by line.

Oil, gas and utilities

PPE compliance at remote sites watched from one dashboard, with alerts on a supervisor's phone.

Compared

Doing it by hand vs. with Ceptory

Without Ceptory

  • A supervisor walks the site a few times a shift and misses everything in between
  • Hours of footage reviewed by hand after an incident
  • Violations recorded on paper, hard to trend

With Ceptory

  • Every worker in the zone checked every 10 seconds, all shift
  • Ask a recorded clip for every violation and get timestamps in minutes
  • Every alert kept with its frame and clip; trends in Insights

Good results

Tips for accurate results

  • Mount cameras so people are at least 80 to 100 pixels tall in the frame; a helmet on a tiny figure can't be judged.
  • Draw the zone tightly around where PPE is required so passers-by outside it don't count.
  • Turn gloves on only for close cameras over workstations.
  • Start with an example video or a recorded clip to see results before wiring live cameras.

Cameras

Works with the cameras you have

Any IP camera or NVR with RTSP or ONVIF, a webcam, or a live stream from OBS, a drone or an encoder. Ceptory Edge runs on a mini PC, NAS or Raspberry Pi on the camera network; nothing is opened to the internet.

FAQ

PPE Detection: common questions

What PPE can Ceptory detect?

Hard hats and safety helmets, hi-vis vests and jackets, and gloves. You choose which items are required on each camera, so a loading dock can require vests only while a construction gate requires helmets and vests.

Can I check a recorded video for PPE violations instead of a live camera?

Yes, and most teams start that way. Upload a clip (up to 2 GB) with the prompt on this page and Ceptory lists every person missing PPE with the timestamp and the missing item. You can then turn the answer into a safety report.

Does it work with my existing CCTV cameras?

Yes. Ceptory works with any IP camera or NVR that gives an RTSP stream or speaks ONVIF, including Hikvision, Dahua, CP Plus, Axis, Reolink, Uniview and UniFi Protect, through the Ceptory Edge agent or the desktop app. No new cameras are needed.

How fast are PPE alerts?

Each camera is checked every 10 seconds by default, and an alert goes out as soon as a check finds someone without the required gear in the PPE zone: to Slack, Teams, Discord, email, a webhook or the Ceptory phone app.

Will one worker trigger hundreds of alerts?

No. Each camera has a re-alert wait (5 minutes by default), so a person without a helmet raises one alert and Ceptory doesn't alert again on the same camera until the wait is over.

Does PPE detection identify workers by face?

No. The PPE check looks for gear on people; it doesn't recognise who they are. Face matching is a separate workflow (face access) that you only turn on where you need it.

Is there a free way to try it?

Yes. Create a free account, upload a clip or run the PPE check on one of our example videos, and see the results before connecting any camera.

Get started

Start ppe detection today

Free to start. Upload a clip or run it on our example footage before you connect a single camera.

A workplace safety frame: workers in hard hats with one worker without a hard hat bracketed. Figures are faceless.