Workplace safety
AI Fire and Smoke Detection from Your CCTV
Ceptory watches camera feeds for flames, smoke, flooding and storm damage and alerts your team with the frame that shows it. Upload footage of an incident to get a minute-by-minute timeline of how it started and spread.
Attach a clip and send. The task is filled in; change it to anything you need.
Hazards
Fire, smoke, flood, storm
Choose any of the four per camera.
Live check
Every 15 s
Whether or not anything moves.
Sensitivity
Low, normal, high
Trade early warning for fewer false alarms.
How it works
Check a clip in minutes, or watch cameras around the clock
Upload a clip
For footage you already have: an incident, a shift, a day on site.
- 01Attach a recording (MP4, MOV and most video formats, up to 2 GB) in the box at the top of this page or in a new dashboard chat.
- 02Send the prompt as it is, or change it: “When does smoke first appear in this video, and where?”
- 03Get the answer with timestamps and frames, ask follow-ups, and export a report to PDF or Word.
Watch for fire, smoke, floods and storms
Pick the hazards and sensitivity, draw the area, and Ceptory checks it every 15 seconds.
- 01Open Cameras and choose Connect a camera. Fire & hazards is already picked when you come from this page.
- 02Choose the source: a webcam on this computer, an IP camera or NVR (RTSP or ONVIF, through Ceptory Edge or the desktop app), a live stream pushed from OBS, a drone or an encoder, or one of our example videos.
- 03Draw the area to watch: the area to watch, such as a warehouse floor, a server room, a kitchen or a storage yard.
- 04Set the rules: which hazards to watch for (fire, smoke, flooding, storm or strong wind) and the sensitivity: higher catches more, with more false alarms.
- 05Choose where alerts go and how long a clip to keep, then save. The camera starts watching straight away.
What it finds
What Fire & Smoke Detection picks up
Flames
Smoke
Flooding
Storm and strong wind
Rules you control
Set it up for your site
- Hazards
- Fire, smoke, flooding and storm, each on or off. All four are on by default.
- Sensitivity
- Low, normal or high. Higher catches more, with more false alarms.
- Area
- Draw the region to watch so a welding bay or a fireplace elsewhere in view doesn't count.
- Re-alert wait
- 10 minutes by default between alerts from the same camera.
Every alert
What each alert includes
- The frame that triggered it, with the person, object or vehicle boxed
- A 10, 20 or 30 second clip around the moment (half before, half after), if you turn clips on
- Camera name, site, time and the rule that fired
- Delivery to Slack, Microsoft Teams, Discord, email or a signed webhook, plus push to the Ceptory phone app and an optional alarm on the monitoring desk
- One click to turn the alert into a full incident report you can export to PDF or Word
Use cases
Where teams use it
Warehouses and storage
Large open spaces where ceiling detectors react late; cameras can see smoke at floor level.
Factories
Machine fires, sparks and smoke on production lines, with the clip for the investigation.
Outdoor yards and car parks
Open areas with no smoke detectors at all: bins, vehicles, scrap and stockpiles.
Basements and low ground
Flooding in car parks, plant rooms and stores before it reaches equipment.
Compared
Doing it by hand vs. with Ceptory
Without Ceptory
- Smoke detectors only work indoors and need smoke to reach the ceiling
- Outdoor areas often have no detection at all
- After a fire, hours of footage reviewed to find the cause
With Ceptory
- Sees flames and smoke wherever a camera points, indoors or out
- Alerts with the frame so staff can judge it in seconds
- Ask the recording where the fire started and get the timeline
Good results
Tips for accurate results
- Video detection adds to your fire alarm system; it does not replace certified smoke and heat detectors.
- Use normal sensitivity first; raise it for high-risk areas and lower it where steam or dust is common.
- Leave hot-work areas (welding, kitchens) out of the zone or watch them at low sensitivity.
Cameras
Works with the cameras you have
Any IP camera or NVR with RTSP or ONVIF, a webcam, or a live stream from OBS, a drone or an encoder. Ceptory Edge runs on a mini PC, NAS or Raspberry Pi on the camera network; nothing is opened to the internet.
FAQ
Fire & Smoke Detection: common questions
Can a CCTV camera detect fire and smoke?
Yes. Ceptory analyses frames from ordinary CCTV cameras for flames and smoke, and also flooding and storm damage. It works with the cameras you already have, through RTSP or ONVIF.
Does this replace smoke detectors?
No. Video detection is an extra layer: it can see fire outdoors and in large spaces where ceiling detectors react late, but it does not replace a certified fire alarm system.
How quickly does it alert?
Each camera is checked every 15 seconds by default. When a check finds fire or smoke in the area, the alert goes out straight away with the frame.
What about steam, dust or sunsets?
Those can look like smoke or fire. Draw the area to exclude them, and use the sensitivity setting: lower sensitivity means fewer false alarms.
Can I analyse footage after a fire?
Yes. Upload the recording and ask when smoke first appeared, where it started and how people evacuated. Ceptory answers with timestamps and can write the incident report.
Get started
Start fire & smoke detection today
Free to start. Upload a clip or run it on our example footage before you connect a single camera.





